Latest News


Current lead times:

Most items will ship out in 3-6 days.
Electric / Hydraulic Pump is a 1 week lead time.

Model 52 Bender is approximately 1-2 weeks.
Model 54 Bender is approximately 2-3 weeks.
HP-110 Horizontal Press 5-7 weeks.

Please be aware that we may ship items in multiple shipments in order to get them to you as fast as possible. If you need anything faster than our current posted lead times, please contact customer service at 423-979-0309 and they may be able to assist you with rushing your order. 

Model 32 Bender - Manual


Show Picture 1Show Picture 2Show Picture 3Show Picture 4Show Picture 5

Show Picture 6Show Picture 7Show Picture 8Show Picture 9Show Picture 10



Model 32 Bender - Manual

Model 32 Bender - Manual



E-mail this product to a friend E-mail this product to a friend


Previous  Up  Next" 

The Model 32 is essentially a super heavy duty version of the Model 3. The Model 3 is the best selling USA made bender in the world. However, when we initially designed it in the mid 1980's it was a mechanical bender targeted at racecar builders who wanted an affordable bender which still produced high quality bends. Hydraulics wasn't added until years later.

Fast forward 25 years and builders have changed gears. Now, rock crawler builders need to bend 2" o.d. x .250" wall dom tubing and thin wall tubing is now more common than it was back then. We knew the basic principle of the Model 3 was near impossible to beat so the answer was to simply make it better. The Model 32 is the result.

Differences between the two benders are:Frame strength has been more than doubled.7/8" diameter 100,000 psi alloy pins were upgraded to 1 1/4" diameter.

A die locking mechanism was designed that both helps bend thin wall tubing as well as very heavy walled tubing by preventing the die from relaxing when not bending. Springback is the #1 cause of wrinkling thin walled tubing.The Model 32 has been designed for mechanical or hydraulic operation from day one. Its hydraulic swivel block rotates on the cylinders true center axis thereby eliminating side load on the ram during bending. This greatly extends the life of the cylinder. A one piece steel ram yoke with quick disconnect pin is now incorporated as well.
An anti- springback ratchet is now included free with the bender. This allowed us to design a new ratchet lever system with more than a 20% reduction in bending effort.Geometry of the bender itself was altered to take better advantage of the new generation 3 followbars thus yielding better bends.

Drive link bolts and sleeves sizes have increased from 1/2" diameter to 3/4" to handle the extra load.

RUGGED ALL STEEL CONSTRUCTION - Designed with durability and affordability in mind. All parts are 100% CNC machined. The frame links are machined from 3/4" thick steel and the drive links are made from 1/2" thick cold rolled steel. Compared to the Model 3's 7/8" diameter pins the Model 32 utilizes extra large 1 1/4" diameter 100,000 PSI alloy pins to handle the tough bends. Fast change bending dies are CNC machined from solid steel billets and carry a lifetime guarantee against breakage. Steel dies eliminate the problems common with other manufacturers' aluminum dies, such as breakage and groove spreading when bending 4130 chromemoly tubing.

LARGE CAPACITY - Bends round tubing and pipe from 1/2" to 2 1/2" O.D. and square tubing from 1/2" to 1-1/2". This bender is rated to bend 2" o.d. x .250" wall DOM steel tubing. Also capable of solid steel up to 1 1/2" diameter.NOTE: To bend round tubing over 2" o.d. x .120" wall, square tubing over 1 1/2" or solids over 1" diameter requires hydraulics.

EASY OPERATION - The Model 32 uses a high-ratio ratchet mechanism to allow you to bend larger tubing sizes comfortably without assistance. For example, the average operator can bend 1 3/4" x .095" wall round mild steel tubing with one hand and 1" x .065" wall tubing with ONE finger. Dies can be changed in under 30 seconds. Bend times are typically in the 30-60 second range for 1" O.D. and above tubing using the ratchet mechanism. Hydraulics may be slightly slower or faster depending on the power unit chosen.

HIGHLY ACCURATE - With the degree indicator wheel standard on every Model 32, accurate bending is simply a matter of watching the pointer until the degree of bend you desire is reached. High contrast yellow markings on a black wheel provide excellent readability while bending.

DIE LOCKING MECHANISM
Standard on every Model 32 is the die locking mechanism. As the die rotates while bending the drive holes in the forming die pass under the lock pin. When the drive hole is below the lock pin, it drops into the drive hole and when pressure is removed from the bender the die's rotation is locked at that position. When bending resumes the ramp machined into the lock pin will automatically lift the pin out of the drive hole. This mechanism combined with the included anti-springback ratchet allows the Model 32 to better bend thin wall tubing as well as the heavier sizes of tubing such as 2" o.d. x .250" wall DOM tubing.

DEGREE POINTER
Standard on every Model 32 is a quick adjust degree indicator wheel. Simply loosen the lower nut as shown in the picture to the right, rotate the degree wheel to zero degrees and using finger force only, tighten in position.

36" TELESCOPING HANDLE
Included free with bender. The new design has twice the bearing area of the old style for longer life and provides ample leverage for tube sizes up to 1 3/4".However, if more leverage is desired for tougher to bend applications, you now can simply obtain a longer piece of standard 1" schedule 40 pipe and insert it into the ratchet lever. Comes standard with a pull pin so the handle may be retracted out of the way when not in use saving valuable floor space.

NEWLY DESIGNED GENERATION 3 FOLLOW BARS
They are half the weight of the older style and utilize bolt-on inserts that are on average 243% stronger. Insert pads are machined to within 1/1000th of a degree to the theoretically perfect angle for optimum bend quality. Inserts are made from a non-galling bearing material to prevent scratching of expensive material. Delrin inserts are also available for use with polished aluminum. A roll pin holds the follow bar in position while loading tubing. With over 600 hours in R&D and tooling preparation, we are confident these are the best die sets on the market today.



Model 32 Bender Testimonials:

Our new friend Jim Harvey, over at HRE.com, is putting together some reviews of the Model 32 and 4. He's doing a great job with videos and explaining the product every step of the way. Thanks Jim, we appreciate it!

http://hre.com/forums/viewtopic.php?f=5&t=1140


The good folks at JD Squared Folks, I have never used abender before I purchased the “Model 32”. I have completed my first projectwith spectacular results. What a wonderful tool is this bender; easy toassemble, easy to operate with smooth accurate results, reflecting the toolbuilders attention to detail. Also added to my tool arsenal, the “NotchMaster”.I am enamored of the robust design. Nothing missing here. I was able to fit myparts with no effort nor error. Bottom line; I love these tools. What I expectfrom “Made in America”. Regards, Thomas


Price: $395.00 


Quantity:  




M32 Round Die Sets
M32 Round Die Sets
Model 32 Floor Pedestal
Model 32 Floor Pedestal
Notchmaster
Notchmaster
M32 Pipe Die Sets
M32 Pipe Die Sets