Model
4 Bender
$1,095
Includes 10-ton 14" stroke cylinder.
|
|
Awesome power!
Bends round tubing from 1/2" to 2 1/2" diameter, square tubing up to 1 1/2", and up to 2" Schedule 40 pipe. Built-in degree indicator makes it simple to make accurate, repeatable bends. Anti-Springback locking lever for better bend control. Heavy-duty construction - pictured here with 1-1/2" diameter tubing. 1" x 8" frame bolts, frame and drive arms are CNC machined from 1" and 3/4" steel plate.  
|
Engineered To Be Reliable !!! - Painstakingly designed to last for years in a hard working fabrication shop. The hydraulic cylinder for instance, swivels in a solid CNC machined steel block that pivots exactly at the cylinder's center, preventing side loads on the cylinder's internals. The pusher block, seen in the lower center of the above photo, employs a unique rotating design and a swiveling bronze wear block so that the cylinder will not experience any up or down loading.
Self Locking, Hydraulic Operation !!! - The Model 4 employs a 10 ton single acting spring return cylinder with a stroke of 10" to 14". It operates up to 4000 p.s.i. With the recommended 14" stroke cylinder, 90 degree bends can be accomplished in less than two complete strokes and 180 bends typically require only three strokes. The 10" stroke cylinder requires three strokes for a 90 degree bend and usually five for a 180 degree bend. During bending, neither the die set nor the workpiece needs to be reset or touched in any way until the bending operation is complete. Using the spring loaded anti-springback lever, the Model 4 will lock the workpiece in position when the cylinder needs to be advanced to the next stroke position, therefore not allowing the workpiece to relax or shift in the bender. This makes possible much tighter radius bends in thinner wall material then can be accomplished on competing benders. Using a 14" stroke cylinder, the first bend stroke can be up to approximately 60 degrees. The second stroke will go to approximately 126 degrees. Bending speed is dependent upon the strength of the material being bent. Usually 6 to 10 degrees of bend per second will be realized. The 14" stroke cylinder takes 8 to 9 seconds to return from full extension. Add it all up and a typical 90 degree bend will take an effortless 20 to 25 seconds, depending on the operator's skill level. Note: Since the pump and cylinder used in the Model 4 is extremely popular, you may already have them. If so you wouldn't need to purchase these items. If you have any questions in regard to this please call for assistance.
Affordable!!! -
The Model 4 Bender comes in several price packages:
* Model 4 Bender less stand, cylinder and pump - $895.
* Model 4 Bender with a Power Team high quality 14" stroke hydraulic cylinder - $1095.
* Model 4 Bender complete with high quality Power Team 14" stroke cylinder and
air/hydraulic pump and hose - ONLY $1565.00
* Model 4 Bender complete with 14" stroke cylinder, fast 1 1/2 h.p. high volume
pump, hydraulic hose and hand control unit - ONLY $2440
Hydraulic Pumps
Fast 1 1/2 H.P. hand-switch controlled, high volume pump with hydraulic hose
- $1345.
Power Team Air/Hydraulic Pump (8-27 in.3/min.) w/ hydraulic hose- $470
Bender Stand - $135.
Die Sets - Generally they are the same price as the Model 3 Bender for the equivalent
size. Call for more info.
 |
Air/Hydraulic
Pump with Hose - $470 Includes 10,000 psi hydraulic hose w/ quick disconnect coupler. Requires
an air compressor. |
 |
4,000 PSI Electric
Pump w/ Hose - $1345 Includes 5,000 psi hydraulic hose w/ quick disconnect coupler. Single-Phase
110VAC. Approximately 3 times the speed of the air/hydraulic pump. |
 (Actual stand is glossy black without decals) |
Model
4 Bender
Pedestal- $135 The Model 4 Bender can be mounted to this optional stand. Heavy duty,
36 inch tall, can be bolted to a concrete floor. |
Prices current as of 6/1/2008
Note: In the description column,
the numbers in the parenthesis [ ex: (6.5-180) ] designate the die set's center
line radius and maximum normal degree of bend. In the example above the (6.5-180)
would designate a die set with a center line radius of 6.5" and would be capable
of producing a complete 180 degree bend. As of 2003, all Model 4 Bender die sets are manufactured
as 180 degree styles. The "Center Line Radius" is the bend radius as measured
from the center rotation point of the die to the middle of the tubing. The 'Minimum
Wall Thickness' column represents the minimum wall thickness for consistent
high quality wrinkle free bends. Wall thicknesses less than .083" may require
an anti-springback block added to the followbar to help limit springback and
prevent wrinkling. All die sets will bend up to .120" wall. Greater wall thicknesses
may be bent with the smaller O.D. tubing and pipe up to the maximum power of
the bender.
Metric and custom die sets are available and are priced closely to comparable size of inch series tooling.
Unfortunately, due to the extreme increases in the price of steel, as of 6/1/2008 we have been forced to raise some of our prices between 5 and 20%. We held off as long as we could. Let's all hope steel prices stabilize soon.
| Part# | Description | Minimum Wall Thickness | Price |
Click to Buy |
|---|---|---|---|---|
| Model
4 Bender Round Tube Die Sets |
||||
| 100714 | M4B Round Tube Die Set - 1/2" (2.25-CLR) | .058" | $135 | |
| 100715 | M4B Round Tube Die Set - 1/2" (3-CLR) | .049" | $145 | |
| 100716 | M4B Round Tube Die Set - 5/8" (2.25-CLR) | .049" | $135 | |
| 100717 | M4B Round Tube Die Set - 3/4" (2.25-CLR) | .058" | $135 | |
| 100718 | M4B Round Tube Die Set - 3/4" (3-CLR) | .058" | $145 | |
| 100719 | M4B Round Tube Die Set - 3/4" (4.5-CLR) | .049" | $225 | |
| 100721 | M4B Round Tube Die Set - 7/8" (3-CLR) | .058" | $145 | |
| 100722 | M4B Round Tube Die Set - 7/8" (4.5-CLR) | .058" | $225 | |
| 100723 | M4B Round Tube Die Set - 7/8" (5.5-CLR) | .058" | $250 | |
| 100725 | M4B Round Tube Die Set - 1" (3-CLR) | .058" | $155 | |
| 100726 | M4B Round Tube Die Set - 1" (3.5-CLR) | .058" | $175 | |
| 100727 | M4B Round Tube Die Set - 1" (4.5-CLR) | .058" | $235 | |
| 100729 | M4B Round Tube Die Set - 1" (5.5-CLR) | .058" | $260 | |
| 100732 | M4B Round Tube Die Set - 1 1/8" (3.5-CLR) | .083" | $180 | |
| 100734 | M4B Round Tube Die Set - 1 1/8" (4.5-CLR) | .058" | $245 | |
| 100736 | M4B Round Tube Die Set - 1 1/8" (5.5-CLR) | .058" | $270 | |
| 100739 | M4B Round Tube Die Set - 1 1/4" (3.5-CLR) | .083" | $180 | |
| 100740 | M4B Round Tube Die Set - 1 1/4" (4.5-CLR) | .058" | $245 | |
| 100742 | M4B Round Tube Die Set - 1 1/4" (5.5-CLR) | .058" | $270 | |
| 100746 | M4B Round Tube Die Set - 1 3/8" (4.5-CLR) | .095" | $265 | |
| 100748 | M4B Round Tube Die Set - 1 3/8" (5.5-CLR) | .065" | $280 | |
| 100749 | M4B Round Tube Die Set - 1 3/8" (6.5-CLR) | .065" | $290 | |
| 100750 | M4B Round Tube Die Set - 1 1/2" (4.5-CLR) | .095" | $265 | |
| 100753 | M4B Round Tube Die Set - 1 1/2" (5.5-CLR) | .083" | $280 | |
| 100756 | M4B Round Tube Die Set - 1 1/2" (6.5-CLR) | .058" | $290 | |
| 100760 | M4B Round Tube Die Set - 1 5/8" (5.5-CLR) | .083" | $290 | |
| 100762 | M4B Round Tube Die Set - 1 5/8" (6.5-CLR) | .083" | $300 | |
| 100764 | M4B Round Tube Die Set - 1 3/4" (5.5-CLR) | .095" | $300 | |
| 100766 | M4B Round Tube Die Set - 1 3/4" (6.5-CLR) | .083" | $315 | |
| 100768 | M4B Round Tube Die Set - 1 7/8" (6.5-CLR) | .095" | $345 | |
| 100770 | M4B Round Tube Die Set - 2" (6.5-CLR) | .095" | $345 | |
| 100772 | M4B Round Tube Die Set - 2-1/4" (6.5-CLR) | .120" | $425 | |
| 100775 | M4B Round Tube Die Set - 2-1/2" (6.5-CLR) | .120" | $475 | |
| 100774 | M4B Round Tube Die Set - 2-3/8" (6.5-CLR) | .120" | $450 | |
| Model
4 Bender Sch. 40 Pipe Die Sets |
||||
| 100659 | M4B Pipe Die Set - 1/2" Pipe, .840" OD (3-CLR) | Sch 40 | $150 | |
| 100661 | M4B Pipe Die Set - 3/4" Pipe, 1.050" OD (3.5-CLR) | Sch 40 | $175 | |
| 100662 | M4B Pipe Die Set - 3/4" Pipe, 1.050" OD (4.5-CLR) | Sch 40 | $240 | |
| 100664 | M4B Pipe Die Set - 1" Pipe, 1.315" OD (3.5-CLR) | Sch 40 | $185 | |
| 100665 | M4B Pipe Die Set - 1" Pipe, 1.315" OD (4.5-CLR) | Sch 40 | $250 | |
| 100666 | M4B Pipe Die Set - 1" Pipe, 1.315" OD (5.5-CLR) | Sch 40 | $270 | |
| 100672 | M4B Pipe Die Set - 1 1/4" Pipe, 1.660" OD (4.5-CLR) | Sch 40 | $285 | |
| 100676 | M4B Pipe Die Set - 1 1/4" Pipe, 1.660" OD (5.5-CLR) | Sch 40 | $290 | |
| 100678 | M4B Pipe Die Set - 1 1/4" Pipe, 1.660" OD (6.5-CLR) | Sch 40 | $305 | |
| 100680 | M4B Pipe Die Set - 1 1/2" Pipe, 1.900" OD (5.5-CLR) | Sch 40 | $330 | |
| 100682 | M4B Pipe Die Set - 1 1/2" Pipe, 1.900" OD (6.5-CLR) | Sch 40 | $345 | |
| 100686 | M4B Pipe Die Set - 2" Pipe, 2 3/8" (6.5-CLR) | Sch 40 | $450 | |
| Model
4 Bender Square Die Sets |
||||
| 100691 | M4B Square Die Set - 1/2" (3-CLR) | .083" | $160 | |
| 100692 | M4B Square Die Set - 1/2" (5.5-CLR) | .083" | $280 | |
| 100693 | M4B Square Die Set - 3/4" (3-CLR) | .095" | $165 | |
| 100694 | M4B Square Die Set - 3/4" (4.5-CLR) | .095" | $265 | |
| 100696 | M4B Square Die Set - 1" (3.5-CLR) | .095" | $195 | |
| 100697 | M4B Square Die Set - 1" (4.5-CLR) | .083" | $280 | |
| 100699 | M4B Square Die Set - 1" (5.5-CLR) | .083" | $300 | |
| 100701 | M4B Square Die Set - 1" (6.5-CLR) | .083" | $320 | |
| 100703 | M4B Square Die Set - 1 1/4" (4.5-CLR) | .095" | $285 | |
| 100705 | M4B Square Die Set - 1 1/4" (5.5-CLR) | .083" | $300 | |
| 100707 | M4B Square Die Set - 1 1/4" (6.5-CLR) | .083" | $320 | |
| 100709 | M4B Square Die Set - 1 1/2" (5.5-CLR) | .083" | $320 | |
| 100711 | M4B Square Die Set - 1 1/2" (6.5-CLR) | .083" | $335 |
|
* Some dies available with 7.5" CLR. - Call for pricing
Warranty
All products sold by JD Squared carry a warranty of 1 year from the date of
purchase,
limited to normal operation per the Model
4 Instruction Manual
More Pictures
Lower frame painted red for clarity of demonstration, standard is glossy black.
Shown bending 1 1/2" x .095" wall tubing to a 4 1/2" radius. On the right is the hydraulic pump control. All links are 3/4" thick CNC machined steel. Complete with pump the Model 4 weighs 225 lbs. The pedestal is optional.
In the lower left corner of the picture above you can see the anti-springback lever. It is spring loaded and prevents the workpiece from moving when the hydraulic cylinder is being re-positioned for the next stroke.
In the top two pictures above can be seen the pusher block with its bronze pivot block. The handle makes re-positioning the hydraulic ram fast and easy. The average cylinder retract and re-position time is approximately 8-10 seconds. With the 2 HP pump the Model 4 bender strokes 60 degrees in 6-10 seconds.
The Model 4 is shown above in its retracted state. With a 14" stroke cylinder,
it can bend approximately 60 degrees in one shot. After the ram extends the
anti-springback lever automatically engages to prevent the workpiece from moving.
| © Copyright 2008 JD Squared, Inc. All Rights Reserved |